Low pressure after filtration is usually a hydraulic or maintenance problem, not proof that filtration cannot work.
Evidence snapshot
- NHMRC (2025): The Australian Drinking Water Guidelines are a risk-management framework, not a single national pass/fail law. They separate health-based, aesthetic and operational considerations.
- NSF (2026): NSF standard numbers are not quality rankings. NSF/ANSI 42 covers stated aesthetic claims, 53 health-effect claims, 44 softeners, 55 UV and 58 point-of-use RO; the exact certified claim still has to be checked.
- Water Analytics Australia (2026): WAA's current whole-home page describes staged sediment, carbon and complementary treatment, optional under-sink RO, consultation and ongoing filter support. Exact claims still need to match the supplied configuration.
These figures and standards are reference points, not a diagnosis of one home. Local water data, premises plumbing, flow and maintenance determine how they apply.
Measure flow and pressure under the same conditions
Start with the property itself. Record static pressure and pressure at a known flowing outlet before and after treatment. A shower that feels weak is useful evidence, but it cannot separate a loaded cartridge from a partly closed valve or a wider supply change. Ask for the clean-system pressure drop and the design flow in litres per minute. Repeat the same check after service so the figures are comparable.
The limit to keep visible
Likely causes include a loaded sediment cartridge, a partly closed valve, an undersized housing, a blocked pre-filter, incorrect bypass position or an unrelated supply-pressure change.
Official guidance describes population-level or supply-level risk; a component test describes stated test conditions; a household observation describes one property. None should silently stand in for another. Connect them only where the source, configuration and operating conditions genuinely match.
How to verify the outcome
A useful diagnosis compares pressure before and after the system under the same flow condition.
Check the conditions that can move the result: flow, pressure, temperature, water chemistry, media quantity, treated volume and time since service. A technology can be well suited in principle and still be undersized or poorly maintained in practice. Put the relevant operating range into the proposal.
A practical household check
| Record | What to capture | Why it changes the decision |
|---|---|---|
| Pattern | Compare outlets, hot/cold and first draw | Locates the likely source |
| Baseline | Measure pressure at a known flow | Makes service changes comparable |
| Escalation | Check utility and safety advice | Avoids masking a wider problem |
Use the same notes when requesting more than one quote. Suppliers then have to answer the same water, flow and ownership brief rather than redefining the problem around their preferred product.
Where Water Analytics Australia fits
WAA's role is to turn the household brief into a proportionate design. That starts with source water, treatment goal, realistic peak flow, available pressure, installation access and the preferred service approach. Depending on the job, the answer may be whole-home staged treatment, point-of-use RO, the benchtop system or a combination. The written proposal should explain why each stage is present, the conditions behind each claim and what the customer will need to maintain.
Related WAA guides
- Brown, Cloudy or Black Tap Water: A Safe Troubleshooting Guide
- Why Is My Filter Cartridge Turning Brown So Fast?
- WAA Full Home Water Refining Systems
Common questions
What should I check before opening the filter housing?
Check current utility notices, compare hot and cold water at several taps, note when the issue began and record pressure at a known flow. Isolate water only when the safety and source questions are clear.
What is the most useful measurement?
Use the measurement that matches the decision. Record static pressure and pressure at a known flowing outlet before and after treatment. A shower that feels weak is useful evidence, but it cannot separate a loaded cartridge from a partly closed valve or a wider supply change. Ask for the clean-system pressure drop and the design flow in litres per minute. Repeat the same check after service so the figures are comparable.
What should WAA receive before recommending a system?
Provide the postcode, water source, household size, bathroom count, busiest-use pattern, observed issue, desired result and any laboratory report with its units and sample point.
Sources and further reading
- NHMRC: Australian Drinking Water Guidelines, version 4.0
- NSF: Standards for water treatment systems
- Water Analytics Australia: Full Home Water Refining Systems
The next useful step
Write down the source, the result you want, peak-use flow and the evidence already available. Then ask for a recommendation that gives every stage a defined job, states the operating assumptions and includes the service plan. That is enough detail to compare a WAA proposal with any alternative without relying on fear or brochure language.